考虑岩石抗拉强度受围压影响的地层破裂压模型

预测地层破裂压力是地下流体注入工程中的关键问题，关系到工程的稳定性和安全性。根据地测资料，岩石的抗拉强度会随着围压产生变化，然而目前常见的地层破裂压预测模型均未考虑该因素。基于厚壁圆筒法，针对2种砂岩开展不同围压条件下的砂岩致裂试验，根据试验数据，计算各组试验中试样的抗拉强度，并拟合围压与岩石抗拉强度的关系函数。研究岩石抗拉强度随围压变化的规律，提出能在实际地层中表征该规律的参数，基于该参数对现有的地层破裂压模型进行修正，并结合实测数据验证修正模型的可靠性。研究结果表明:岩石的抗拉强度随着围压的增加呈现明显的线性正相关关系，低围压下，新模型的预测结果与实测数据较为接近。随着围压增加，二者的差异逐渐增大，说明选取的特征参数在低围压下能较好地描述抗拉强度受围压的影响效应，而高围压下参数的取值需进一步研究。     

电气柜疲劳强度校核及结构优化

针对多孔闭孔型发泡硅橡胶D型空心密封条的超弹性特性,通过试验找出了密封条回弹力与压缩量之间的关系,提出了密封条满足IP X5的判别方程式,同时对方程式进行了试验验证,最后对密封条进行了阿累尼乌斯图寿命推算,为变流器柜门IP防护设计提供了重要参考。     

分子识别作用下光催化降解偶氮染料酸性红GR

合成了β-环糊精(β-CD)与偶氮染料酸性红GR(ARGR)的包结物,并采用红外光谱仪对ARGR、β-CD及β-CD与ARGR的包结物进行了表征,表征结果显示,β-CD与ARGR的包结物的特征峰的峰形和强度与β-CD相似,但峰位有明显的偏移,说明ARGR进入了β-CD空腔与β-CD发生了分子识别作用。采用TiO2作为催化剂,研究了β-CD分子识别后ARGR的光催化降解行为,实验结果表明,在ARGR质量浓度为20.0 mg/L、β-CD浓度为1.8×10-5 mol/L、体系pH为4.0、TiO2加入量为1.0 g/L、光催化反应时间为60 min的条件下,经β-CD分子识别后ARGR的光催化降解率可达100%。     

基于RFPA2D复合局部挠曲岩体数值模拟

为研究复合局部挠曲岩体强度特征以及破坏规律，采用岩石真实破裂软件RFPA^2D，对水平层面挠曲30°，45°，60°，75°的复合岩体进行单轴压缩试验模拟。模拟结果表明:挠曲角为30°，45°，60°，75°的复合岩体破坏面几乎与挠曲段夹层重合，其挠曲端部均产生了垂直于挠曲段夹层的裂纹；复合单斜岩体与复合挠曲岩体破坏面的形成因素大致相同，夹层强度是2种岩体失稳的主要因素；复合挠曲岩体单轴抗压强度随挠曲角增大同样呈“U”型变化，与单斜岩体变化趋势一致；当水平层状岩体发生挠曲后，其单轴抗压强度减小，当挠曲角为60°时，强度降低25.19%，当挠曲角为75°时，强度降低0.17%。；随着均质系数m的增大，复合挠曲岩体单轴抗压强度以及轴向应变均出现逐渐递增的趋势，且不同m值，其岩体裂隙扩展方式具有明显差别。     

岩石溶蚀的表现特征及其对物理力学性质的影响

本文以微晶白云石大理岩和黏土质长石砂岩为研究对象,以现场实测及室内试验资料为基础,对岩石溶蚀的表现特征及其对表层物理力学性质的影响进行了研究。研究表明:1)在岩石发生溶蚀的区域,由表及里易溶性矿物成分和易迁移元素氧化物的含量逐渐增加、黏土矿物含量和烧失率逐渐减少,岩样的微观结构也发生了变化,主要表现为岩石表层溶孔、溶隙发育,易溶矿物颗粒表面出现溶孔、溶坑、颗粒间出现溶蚀裂隙等;2)溶蚀使岩石表层强度降低、吸水率增大,溶蚀愈严重表层强度越低、均匀性愈差,吸水率愈大;溶蚀还使岩石的孔隙度及孔隙尺寸明显增大。     

基于强度折减法的港珠澳大桥沉管隧道干坞工程高边坡稳定性分析

在列举和分析比较当前岩土工程领域边坡稳定性分析的各种主要方法的基础上,概述了强度折减法的基本原理、主要特点和优势,并以港珠澳大桥沉管隧道干坞大型临时工程拟建场地的岩质高边坡为实例,应用强度折减法基于FLAC3D软件对该边坡的稳定性进行了计算和分析,确定了边界条件和强度参数,计算了该边坡的安全系数,结果表明自然工况下边坡处于稳定状态,底部开挖以后边坡趋于欠稳定状态,同时指出了边坡的关键变形部位,可为后续的设计和施工提供参考。     

基于GH-B强度准则的节理岩质边坡稳定性分析

在岩质边坡工程数值模拟计算分析中,其难题之一就是如何较准确地确定岩体强度参数,而边坡岩体抗剪强度是影响计算分析成果的控制因素,也是支护设计成败的关键所在。采用GH-B强度准则对深水河大桥4号桥墩边坡进行了稳定性分析,同时与采用M-C强度准则的模拟结果进行了对比分析。结果表明:GH-B强度准则采用基于应力水平的塑性流动法则,更好地体现了节理岩体的变形和破坏机理,可有效反映岩体的非线性破坏特征,更加接近于工程实际,适于节理岩体的强度计算及稳定性分析。     

Rapid decolorization of Acid Orange II aqueous solution by amorphous zero-valent iron

Some problems including low treatment capacity, agglomeration and clogging phenomena, and short working life, limit the application of pre-treatment methods involving zero-valent iron (ZVI). In this article, ZVI was frozen in an amorphous state through a melt-spinning technique, and the decolorization effect of amorphous ZVI on Acid Orange II solution was investigated under varied conditions of experimental variables such as reaction temperature, ribbon dosage, and initial pH. Batch experiments suggested that the decolorization rate was enhanced with the increase of reaction temperature and ribbon dosage, but decreased with increasing initial solution pH. Kinetic analyses indicated that the decolorization process followed a first order exponential kinetic model, and the surface-normalized decolorization rate could reach 2.09 L/(m². min) at room temperature, which was about ten times larger than any previously reported under similar conditions. Recycling experiments also proved that the ribbons could be reused at least four times without obvious decay of decolorization rate and efficiency. This study suggests a tremendous application potential for amorphous ZVI in remediation of groundwater or wastewater contaminated with azo dyes.     

酒石酸淋洗过程中土壤重金属解吸动力学特征

采用批处理淋洗的方法,研究了酒石酸淋洗修复张士污灌区土壤过程中镉、铅、铜、锌4种重金属离子解吸动力学特征。结果表明,酒石酸在12h条件下,达到对污染土壤中镉离子的最大去除率,铅、铜、锌3种重金属离子达到最大去除率则需要24h。4种重金属离子的解吸动力学过程可以用Elovich方程很好的描述,说明酒石酸去除重金属离子的过程是一种非均相扩散过程。此外,解吸速率曲线显示,反应初期相同时刻上酒石酸对铅离子的解吸速率最快,其次是铜和锌,最后是镉离子;反应后期同一时刻上铜和锌的解吸速率大于铅和镉。     

Effect of chemical and thermal activations on the properties of rice husk ash-based solidified wastes

Strength development,leachability and microstructure of heavy metals from the solidified waste using synthesis rice husk ash (sRHA) and lime blended at the weight ratio of 1:1 were used as binders.The heavy metal-containing sludge was used at the level of 0 wt.%,30 wt.%,and 50 wt.% dry weight,respectively.The sample specimens with and without 1.5 wt.% of sodium silicate (SiO 2 /Na 2 O=1.0) were cured under the ambient condition and elevated temperature curing at 50°C for 24 hr.Experimental results showed that the introduction of sodium silicate solution and elevated temperature curing to sRHA-based solidified waste containing 30 wt.% of heavy metal sludge gave one day strength of 20 kg/cm 2 compared to 0.9 kg/cm2 for the control sample.XRD patterns indicated that most metal-sulfides present in the sludge were appeared in the solidified waste and SEM coupled with EDX techniques reveal these metal-sulfide particles were trapped within the lime-sRHA matrices.In addition,cumulative leaching behavior by tank test (EA NEN 7375:2004) showed that solidified waste containing up to 30 wt.% of heavy metal sludge was suitable to dispose in a secured landfill.